Jiangxi spiral chute manufacturer

Jiangxi spiral chute manufacturer

Jiangxi Spiral Chute Manufacturer 1 explains that the chute sorting includes an inclined flow sorting process. The mortar is fed to a partially inclined inclined chute or slope, and with the assistance of water flow, the mineral particle group is loose and layered. The upper layer of light mineral materials is quickly discharged from the outside of the groove, while the lower layer of minerals with high specific gravity are retained inside the groove or slowly discharged from the lower part. After being distinguished and connected, concentrate and tailings can be obtained. Fiberglass spiral chutes are equipment for mining and beneficiation, making them particularly ideal for mineral mining along coasts, rivers, beaches, and streams. The equipment has the characteristics of appropriate structure, simple installation, small footprint, simple operation, stable beneficiation, clear screening of minerals, high yield, high efficiency, high beneficiation concentration ratio, high recovery probability, and stable operation. There are also advantages such as small weight, moisture resistance, rust resistance, corrosion resistance, and strong adaptability to fluctuations in ore feed volume, concentration, particle size, and grade. Video of spiral chute machine: Jiangxi spiral chute manufacturer II. Use the method to erect the spiral chute, calibrate the vertical line, fix it in the proper direction with iron frame or wood, and let the mineral sand be sent to the two ore feeding ports above the spiral by mortar pump, participate in water filling, adjust the density of the mineral slurry, and the mineral slurry naturally swirls from top to bottom, generating a single consistency in the flow speed of the rotating slope to obtain centrifugal force The difference in state is achieved by separating the ore and sand through the gravity of the swirling flow and the effect of this centrifugal force. The selected ore flows into the concentrate hopper and is piped out, while the tailings are discharged into the tailings hopper and moved to the sand tank through a pipeline. Then, they are discharged by a slurry pump, completing the entire beneficiation process. Advantages or Characteristics of Jiangxi Spiral Chute Manufacturer 3: High efficiency, high recycling rate, and correct mineral sorting; 2. No power required; 3. Lightweight, rust resistant, durable, wear resistant, and corrosion-resistant; 4. Low cost and long service life; 5. It is applicable to the fluctuation of feeding amount, density, Granularity and grade. The friction force on the surface of 6 diamond sand makes the beneficiation efficiency better than other plastic surfaces. Jiangxi spiral chute manufacturer IV. Structural composition. The spiral chute is composed of six parts, including a feeding homogenizer, a feeding chute, a rotating chute, a product intercepting chute, an equipment gathering hopper, and a slot bracket (including a cross or triangular frame). The spiral groove connected by the rotating plate is a key accessory. The spiral plate is made of fiberglass (fiberglass reinforced coal gangue) and connected together through screws. The sorting surface of the rotating groove has one layer of pre designed durable wear-resistant layer. It has the advantages of lightweight, sturdy, and durable consumer goods. The spiral groove is equipped with a multi tube feeding homogenizer to screen minerals evenly, which is not cumbersome to operate. The mineral sorting equipment is freely stacked on the cross (or tripod) of the support table. The evenly distributed mortar is slowly fed to the spiral groove surface through the feeding groove installed at the head of the rotating groove, and the selection is carried out. The bottom of the rotating groove is installed in a valve block type new equipment to obtain the groove, allowing the sorted new products to be divided into three (or four) new products according to grade along the radial direction. Change the selection width of each new device by adjusting the position of the valve block. The new product gathering bucket is a concentric circular tube that distinguishes and converges the intercepted multi head ore flow. The cross-section of the fiberglass chute and the change in slope of the curve are particularly applicable for the selection of fine-grained materials. 5、 Purpose. This equipment is used to separate iron ore, ilmenite, ferrochrome, ferrosulfide, zircon, Rutile, monazite, phosgenite, wolframite, sand tin, tantalum niobium ore, niobium and other non-ferrous metals, rare mineral metals and this non gold mineral due to the difference in density and specific gravity. Jiangxi Spiral Chute Manufacturer Jiangxi Spiral Chute Manufacturer

Jiangxi spiral chute manufacturer